FIVE STAR FINISHING PUTTY
Body Fillers & Putties...
5066 & 5067
Polyester Premium Finishing Putty
5 STAR AUTOBODY PRODUCTS - Premium Polyester Finishing Putty is effortless to spread and self-levels to a smooth, easy-to-sand surface that is pinhole free – improving your cycle time. The advanced easy-powder formula increases the sanding window. #5066 & #5067 provide excellent results for that invisible repair every time whether over body filler, sand scratches, pinholes, aged OEM topcoats, steel, aluminum, galvanized and other zinc-coated metals, fiberglass and a wide variety of other substrates.
Products:
5066 Polyester Premium Finishing Putty | 16 oz. | 12/cs
5067 Polyester Premium Finishing Putty | 30 oz.
PRODUCT NUMBER DESCRIPTION
#5066 – PREMIUM FINISHING PUTTY (16 OZ) 12/CS
#5067 – PREMIUM FINISHING PUTTY (30 OZ)
DESCRIPTION:
5 STAR AUTOBODY PRODUCTS - Premium Polyester Finishing Putty is effortless to
spread and self-levels to a smooth, easy-to-sand surface that is pinhole free –
improving your cycle time. The advanced easy-powder formula increases the
sanding window. #5066/#5067 provides excellent results for that invisible repair
every time whether over body filler, sand scratches, pinholes, aged OEM
topcoats, steel, aluminum, galvanized and other zinc-coated metals, fiberglass
and a wide variety of other substrates.
PRODUCT USES:
Use for minor body work and surface imperfections (1/8” thick or less) such as
sand scratches, chips, scratches and pinholes. Ideal for use as a finish coat
over body filler.
TYPICAL SUBSTRATES:
Steel
Aluminum
Fiberglass
Body Filler
Wood
2K Primers
Aged, sanded OEM Topcoats
Galvanized and other zinc-coated steel
SMC – can be used for cosmetic repairs. For structural repairs prone to high degrees of stress and flexibility, use an SMC repair product.
SURFACE PREPARATION:
1. Clean surface. Remove all dirt, oil, grease and wax with a Wax & Grease
Remover.
2. Make sure surface is dry before repairing.
3. Use 80 – 180 grit disc to featheredge paint for good mechanical adhesion.
MIXING:
For best results, bring putty and provided hardener to room temperature (minimum
temperature 65°F). Knead hardener tube before use. Place a 4" diameter puddle of
putty on clean mixing surface; we recommend a non-absorbent plastic mixing board
(puddles larger than 4" in diameter will require additional hardener) or,
measure hardener 2% by weight - 50 to 1 ratio. Add a ribbon of cream hardener
from edge to edge across the center of the putty puddle. Mix thoroughly using a
folding motion with a plastic spreader until uniform color is achieved. At room
temperature (65°F) approximate setting time is 3-5 minutes.
APPLICATION:
1. Using a plastic spreader, apply a thin layer of putty to surface, using firm
pressure for maximum adhesion.
2. Apply additional layers, building up damaged area higher than the surrounding
surface to allow for sanding of the putty. Do not apply over fresh or uncured
coatings.
FINISHING:
When material has hardened, in approximately 15 minutes, sand with 100 - 180
grit sandpaper followed by 220 - 400 grit if desired.
TOPCOATING:
May be topcoated with polyester, 2K urethane or 1K primer. Refer to paint
manufacturer's instructions for topcoat application.
TECHNICAL INFORMATION:
Appearance as Packaged: Aqua
VOC: Packaged: 278 g/l - Applied: 2.2 g/l
Weight Per Gallon (Density): 7.85 pounds (Average)
Maximum Recommended Thickness (sanded): 1/8"
Viscosity @ 77°F: 10,400 – 15,200 cps
Gel Time @ 77°F: 3.0 – 5.0 minutes
Shore "D" Hardness Values @ 24 hours: 65-75
Sanding Time @ 77° F: 15 minutes
Maximum Heat: 200°F for 30 minutes
Catalyst Required: Benzoyl Peroxide
Catalyzation Ratio: 2% by weight (50:1 ratio)
Exotherm Temperature: 210°F - 230°F
Tack Free Time: 8 – 10 minutes
Corrosion Resistance: Excellent
Part #: FIVE.5067
Price and Units
Units: 30oz
Units: 30oz Product Links: MSDS Product Information Technical Data Sheet |