//


PURE WHITE ACRYLIC URETHANE

SERIES 700
Low VOC Urethane Paint
High Performance Urethane Single Stage - 2.8 VOC

PRODUCT DESCRIPTION:
ADVANTAGE #700 Series 2.8 VOC Acrylic Urethane Colors are high solids, high gloss, low VOC coatings intended for use as a protective maintenance coating for automotive and industrial applications, surfaces exposed to humidity, chemicals and corrosive elements.

#700 SERIES CUSTOM COLOR/CATALYST:
HIGH PERFORMANCE URETHANE SINGLE STAGE SERIES 2.8 VOC - GALLON
Gloss Black #700-01
Hot Rod Black #701-01
Brilliant Black Pearl #702-01
Gloss White #703-01
Fleet White #704-01
Pure White #705-01
Oxford White #707-01
Charcoal Mist Metallic #708-01
Galaxy Silver #709-01
Viper Red #710-01
Swift Red #711-01
Candy Apple Red #712-01
International Harvester Red #713-01
Allis Chalmers Orange #714-01
New Cat Yellow #715-01
School Bus Yellow #716-01
John Deere Yellow #717-01
John Deere Green #718-01
Ford Blue #719-01
Urethane Catalysts (Quart):
2.8 VOC High Performance Urethane Paint Catalyst #729-04
Premium Low VOC Reducer #730-04
 

DIRECT TO METAL ADHESION:
NOTE: Performance is better when using DTM primer under #700 series paint.

POT LIFE:
Pot life will be about 3-5 hours at 77 F.

MIXING DIRECTIONS (4:1):
2.8 VOC
 
4 PARTS #700 Series Single Stage
1 PART #729 Catalyst
1 PART #730 Reducer or quality grade Low VOC urethane reducer
 

SURFACE PREPARATION:
1. Wash area thoroughly with soap and water to remove contaminates that solvent based cleaners cannot remove effectively.
2. Clean area with Wax and Grease Remover.
3. Use a tack cloth to remove any surface contaminates that may have settled on the repaired areas prior to paint application.
4. Apply #700 series High Performance Urethane Single Stage Color.

APPLICATION DIRECTIONS:
Adjust air pressure to 40-50 psi at gun for gravity, siphon feed guns or HVLP use 6-10 psi at air cap. Apply 2-3 medium coats (maximum 2 mils wet per coat) or until hiding is achieved. Allow a 15-20 minute flash time between coats and before force drying.

DRY TIMES AT 77F:  
FLASH TIME 15-20 MINUTES
TO DELIVER 16-24 HOURS
   
FORCE DRYING AT 140F:  
PURGE TIME 15 MINUTES
BAKE TIME AT 140F 40 MINUTES

RECOATING:
2.8 VOC #700 Urethane Single Stage Color may be recoated after 16-24 hours at 77 F. After 16-24 hours it must be lightly sanded/scuffed before additional color or clearcoat may be applied.

ACCELERATOR & FISHEYE ELIMINATOR:
Accelerator and/or Fisheye Eliminatory is not recommended for use in this product.

CLEAN-UP:
Clean spray equipment immediately after use with Gun Wash, or a high quality lacquer thinner, or compliant solvent depending on area regulations.

TECHNICAL DATA:  
Color: Various  
Catalyst: #729  
Low VOC Reducer: #730  
Mixing ratio (2.8 VOC): 4:1:1  
Weight Solids (RTS): 52 - 70%  
Viscosity #2 Zahn (RTS): 18 - 28 seconds #2 Zahn
Pot Life: 3-5 hours  
Film Build per coat: 1.0-2.0 mils per full wet coat
Coverage: 850 sq.ft. per gallon
@ 1 dry mil
 
Disposal/Safety: See MSDS for this product

Part #: ADV.705

Price and Units

Units: GALLON

Units: GALLON
Product Links:
MSDS
Sales Flyer
Technical Data Sheet
Color Card

//